View B133EW06-V0_7856125.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1 of 32 au optronics corporation product specification auo nbbu spec. version:0.3 ( v ) preliminary specifications ( ) final specifications module 13.3? wxga color tft-lcd model name b133ew06 v0 customer date checked & approved by date note: this specification is subject to change witho ut notice. approved by date kendra wang 7/1/2008 prepared by date emerson huang 7/1/2008 nbbu marketing division / au optronics corporation www.datasheet.co.kr datasheet pdf - http://www..net/
2 of 32 au optronics corporation product specification auo nbbu spec. version:0.3 contents 1. handling precautions ............................ .................................. 4 2. general description ............................. ................................... 5 2.1 general specification .......................... ................................................... .............................................5 2.2 optical characteristics ........................ ................................................... .............................................6 3. functional block diagram ................................................... .. 11 4. absolute maximum ratings........................ ........................... 12 4.1 absolute ratings of tft lcd module............. ................................................... .............................12 4.2 absolute ratings of backlight unit............. ................................................... ...................................12 4.3 absolute ratings of environment ................ ................................................... ..................................12 5. electrical characteristics ...................... ................................. 13 5.1 tft lcd module................................. ................................................... ..........................................13 5.2 backlight unit ................................. ................................................... ...............................................15 6. signal characteristic ........................... .................................. 16 6.1 pixel format image ............................. ................................................... ...........................................16 6.2 the input data format .......................... ................................................... ...........................................17 6.3 signal description/pin assignment.............. ................................................... ..................................18 6.4 interface timing ............................... ................................................... ..............................................19 7. connector description........................... ................................ 22 7.1 tft lcd module................................. ................................................... ..........................................22 8. dynamic test .................................... .................................... 23 8.1 vibration test ................................. ................................................... ................................................23 8.2 shock test spec:............................... ................................................... ..............................................23 9. reliability..................................... ......................................... 24 10. mechanical characteristics..................... ............................. 25 10.1 lcm outline dimension......................... ................................................... .....................................25 11. shipping and package ........................... .............................. 27 11.1 shipping label format ......................... ................................................... ........................................27 11.2 carton package ................................ ................................................... .............................................28 11.3 shipping package of palletizing sequence...... ................................................... ..............................28 12. appendix: edid description ..................... ........................... 29 www.datasheet.co.kr datasheet pdf - http://www..net/
3 of 32 au optronics corporation product specification auo nbbu spec. version:0.3 record of revision version and date page old description new description remark 0.1 2008/03/19 all first edition for customer 18,19 signal description/pin assignment 21 power on/off sequence 25 drawing update 0.2 2008/06/16 29~32 edid description 0.1 2008/07/01 21 power on/off sequence www.datasheet.co.kr datasheet pdf - http://www..net/
4 of 32 au optronics corporation product specification auo nbbu spec. version:0.3 1. handling precautions 1) since front polarizer is easily damaged, pay att ention not to scratch it. 2) be sure to turn off power supply when inserting or disconnecting from input connector. 3) wipe off water drop immediately. long contact wi th water may cause discoloration or spots. 4) when the panel surface is soiled, wipe it with a bsorbent cotton or other soft cloth. 5) since the panel is made of glass, it may break o r crack if dropped or bumped on hard surface. 6) since cmos lsi is used in this module, take care of static electricity and insure human earth when handling. 7) do not open nor modify the module assembly. 8) do not press the reflector sheet at the back of the module to any directions. 9) in case if a module has to be put back into the packing container slot after once it was taken out from the container, do not press the cent er of the led lamp reflector edge. instead, press at the far ends of the led lamp refl ector edge softly. otherwise the tft module may be damaged. 10) at the insertion or removal of the signal inter face connector, be sure not to rotate nor tilt the interface connector of the tft module. 11) after installation of the tft module into an en closure (notebook pc bezel, for example), do not twist nor bend the tft module even momentary. at designing the enclosure, it should be taken into consideration th at no bending/twisting forces are applied to the tft module from outside. otherwise t he tft module may be damaged. 12) small amount of materials having no flammabilit y grade is used in the lcd module. the lcd module should be supplied by power complied wit h requirements of limited power source (iec60950 or ul1950), or be applied exemptio n. 13) the lcd module is designed so that the led in i t is supplied by limited current circuit (iec60950 or ul1950). do not connect the led in haz ardous voltage circuit. www.datasheet.co.kr datasheet pdf - http://www..net/
5 of 32 au optronics corporation product specification auo nbbu spec. version:0.3 2. general description b133ew06 v0 is a color active matrix liquid crystal display composed of a tft lcd panel, a driver circuit, and backlight system. the screen fo rmat is intended to support the wxga (1280(h) x 800(v)) screen and 262k colors (rgb 6-bi ts data driver) without backlight inverter. all input signals are lvds interface compatible. b133ew06 v0 is designed for a display unit of noteb ook style personal computer and industrial machine. 2.1 general specification the following items are characteristics summary on the table at 25 condition: items unit specifications screen diagonal [mm] 337.8 (13.3w?) active area [mm] 286.08 (h) x 178.8 (v) pixels h x v 1280x3(rgb) x 800 pixel pitch [mm] 0.2235 x 0.2235 pixel format r.g.b. vertical stripe display mode normally white white luminance (i led =19ma) note: i led is lamp current [cd/m 2 ] 200 typ.(5 points average) 170 min.(5 points average) (note1) luminance uniformity 1.25 max. (5 points) 1.60 max. (13 points) contrast ratio 600 typ response time [ms] 16 typ nominal input voltage vdd [volt] +3.3 typ. power consumption [watt] 4.0 typ.,4.25 max.( mosaic pattern ) weight [grams] 290 max. physical size [mm] l w t max 296.5 203.5 3.5 typical 296.0 203.0 - min - electrical interface one channel lvds surface treatment glare, hardness 3h, support color 262k colors ( rgb 6-bit ) temperature range operating storage (non - operating) [ o c] o 0 to +50 rohs compliance rohs compliance www.datasheet.co.kr datasheet pdf - http://www..net/
6 of 32 au optronics corporation product specification auo nbbu spec. version:0.3 2.2 optical characteristics the optical characteristics are measured under stab le conditions at 25 (room temperature) : item unit conditions min. typ. max. note white luminance i led =19ma [cd/m 2 ] 5 points average 170 200 - 1, 4, 5. [degree] [degree] horizontal (right) cr = 10 (left) 30 30 40 40 - - viewing angle [degree] [degree] vertical (upper) cr = 10 (lower) 10 20 15 25 - - 8 luminance uniformity 5 points - - 1.25 1 luminance uniformity 13 points - - 1.6 2 cr: contrast ratio 400 600 - 6 cross talk % 4 7 [msec] rising - 4 8 [msec] falling - 12 17 response time [msec] rising + falling - 16 25 8 red x tbd red y tbd green x tbd green y tbd blue x tbd blue y tbd white x 0.283 0.313 0.343 chromaticity of color coordinates (cie 1931) white y 0.299 0.329 0.359 2,8 ntsc % cie 1931 - 45 - www.datasheet.co.kr datasheet pdf - http://www..net/
7 of 32 au optronics corporation product specification auo nbbu spec. version:0.3 note 1: 5 points position (ref: active area) 1 2 3 4 5 h /4 h /4 h /4 h /4 h w w /4 w /4 w /4 w /4 note 2: 13 points position (ref: active area) w /4 w w /4 h h /4 h /4 h /4 h /4 7 9 1 0 w /4 1 8 w /4 1 0 1 0 1 0 1 0 2 3 1 3 1 2 4 5 6 1 1 note 3: the luminance uniformity of 5 or13 points i s defined by dividing the maximum luminance values by the minimum test point luminance note 4: measurement method w13 = maximum brightness of thirteen points minimum brightness of thirteen points maximum brightness of five points w5 = minimum brightness of five points www.datasheet.co.kr datasheet pdf - http://www..net/
8 of 32 au optronics corporation product specification auo nbbu spec. version:0.3 the lcd module should be stabilized at given temper ature for 30 minutes to avoid abrupt temperature ch ange during measuring. in order to stabilize the luminan ce, the measurement should be executed after lighti ng backlight for 30 minutes in a stable, windless and dark room. note 5 definition of average luminance of white (y l ): measure the luminance of gray level 63 at 5 points y l = [l (1)+ l (2)+ l (3)+ l (4)+ l (5)] / 5 l (x) is corresponding to the luminance of the poin t x at figure in note (1). note 6 definition of contrast ratio: contrast ratio is calculated with the following for mula. note 7 definition of cross talk (ct) ct = | y b ? y a | / y a 100 (%) where y a = luminance of measured location without gray level 0 pattern (cd/m 2 ) center of the screen tft - lcd module 50 cm photo detector lcd panel field=2 contrast ratio (cr)= brightnes s on the ?white? state brightness on the ?black? state www.datasheet.co.kr datasheet pdf - http://www..net/
9 of 32 au optronics corporation product specification auo nbbu spec. version:0.3 y b = luminance of measured location with gray level 0 pattern (cd/m 2 ) note 8: definition of response time: the output signals of bm-7 or equivalent are measur ed when the input signals are changed from ?black? to ?white? (falling time) and from ?white? to ?black? (rising time), respectively. the response time inte rval between the 10% and 90% of amplitudes. refer to figure as below . s i g n a l ( r e l a t i v e v a l u e ) "black" tr tf "white" "white" 0% 10% 90% 100% www.datasheet.co.kr datasheet pdf - http://www..net/
10 of 32 au optronics corporation product specification auo nbbu spec. version:0.3 note 8. definition of viewing angle viewing angle is the measurement of contrast ratio R 10, at the screen center, over a 180 horizontal an d 180 vertical range (off-normal viewing angles). th e 180 viewing angle range is broken down as follow s; 90 ( ) horizontal left and right and 90 ( ) vertical, high (up) and low (down). the measureme nt direction is typically perpendicular to the display surface with the scree n rotated about its center to develop the desired measurement viewing angle. www.datasheet.co.kr datasheet pdf - http://www..net/
11 of 32 au optronics corporation product specification auo nbbu spec. version:0.3 3. functional block diagram the following diagram shows the functional block of the 13.3 inches wide color tft/lcd module: www.datasheet.co.kr datasheet pdf - http://www..net/
12 of 32 au optronics corporation product specification auo nbbu spec. version:0.3 4. absolute maximum ratings an absolute maximum rating of the module is as foll owing: 4.1 absolute ratings of tft lcd module item symbol min max unit conditions logic/lcd drive voltage vin -0.3 +4.0 [volt] note 1,2 4.2 absolute ratings of backlight unit item symbol min max unit conditions led current iled - 35 [ma] rms note 1,2 4.3 absolute ratings of environment item symbol min max unit conditions operating temperature top 0 +50 [ o c] note 3 operation humidity hop 5 95 [%rh] note 3 storage temperature tst -20 +60 [ o c] note 3 storage humidity hst 5 95 [%rh] note 3 note 1: at ta (25 ) note 2: permanent damage to the device may occur if exceed maximum values note 3: for quality performance, please refer to au o iis (incoming inspection standard) . twb=39c operating range storage range www.datasheet.co.kr datasheet pdf - http://www..net/
13 of 32 au optronics corporation product specification auo nbbu spec. version:0.3 5. electrical characteristics 5.1 tft lcd module 5.1.1 power specification input power specifications are as follows; symble parameter min typ max units note vdd logic/lcd drive voltage 3.0 3.3 3.6 [volt] pdd vdd power - 0.70 0.75 [watt] note 1/2 idd idd current - 215 250 [ma] note 1/2 i rush inrush current - 0.7 1.5 [a] note 3 vddrp allowable logic/lcd drive ripple voltage - - 100 [mv] p-p note 1 : maximum measurement condition mosaic pattern note 2 typical measurement condition: mosaic pattern note 3 measure condition 90% 10% vin rising time 0v 3.3v 0.5ms www.datasheet.co.kr datasheet pdf - http://www..net/
14 of 32 au optronics corporation product specification auo nbbu spec. version:0.3 5.1.2 signal electrical characteristics input signals shall be low or high-impedance state when vdd is off. signal electrical characteristics are as follows; parameter condition min max unit vth differential input high threshold (vcm=+1.2v) - +100 [mv] vtl differential input low threshold (vcm=+1.2v) -100 - [mv] vcm differential input common mode voltage 0.8 2.0 [v] note: lvds signal waveform www.datasheet.co.kr datasheet pdf - http://www..net/
15 of 32 au optronics corporation product specification auo nbbu spec. version:0.3 5.2 backlight unit parameter guideline for led parameter min typ max units units white luminance 5 points average 170 200 - [cd/m 2 ] ta=25 o c led current (iled) - 18 - [ma] ta=25 o c led power consumption - 3.3 3.5 [watt] ta=25 o c light bar pin assignment: pin no. pin assignment function 1 vout led anode (positive) 2 vout led anode (positive) 3 vout led anode (positive) 4 nc nc 5 fb1 led cathode (negative) 6 fb2 led cathode (negative) 7 fb3 led cathode (negative) 8 fb4 led cathode (negative) 9 fb5 led cathode (negative) 10 fb6 led cathode (negative) www.datasheet.co.kr datasheet pdf - http://www..net/
16 of 32 au optronics corporation product specification auo nbbu spec. version:0.3 6. signal characteristic 6.1 pixel format image following figure shows the relationship of the inpu t signals and lcd pixel format. www.datasheet.co.kr datasheet pdf - http://www..net/
17 of 32 au optronics corporation product specification auo nbbu spec. version:0.3 6.2 the input data format signal name description veedid (3.3v) +3.3v edid power clk eedid edid clock input data eedid edid data input rxin0-, rxin0+ lvds differential data input(red0-red5, green0) rxin1-, rxin1+ lvds differential data input(green1-green5, blue0-b lue1) rxin2-, rxin2+ lvds differential data input(blue2-blue5, hsync, vs ync, de) rxclkin-, rxclkin+ lvds differential clock input vdd +3.3v power supply vss ground note: output signals from any system shall be low o r high-impedance state when vdd is off. www.datasheet.co.kr datasheet pdf - http://www..net/
18 of 32 au optronics corporation product specification auo nbbu spec. version:0.3 6.3 signal description/pin assignment lvds is a differential signal technology for lcd in terface and high speed data transfer device. pin signal description 1 bist/ct1 bist/connector test* 2 vdd power supply (3.3v typ.) 3 vdd power supply (3.3v typ.) 4 v edid ddc 3.3v power 5 clk edid ddc clock / smbus clock 6 data edid ddc data / smbus data 7 rin0- - lvds differential data input (r0-r5, g0) 8 rn0+ + lvds differential data input (r0-r5, g0) 9 vss ground 10 rin1- - lvds differential data input (g1-g5, b0- b1) 11 rn1+ + lvds differential data input (g1-g5, b0-b 1) 12 vss ground 13 rin2- - lvds differential data input (b2-b5,hs,v s, de) 14 rn2+ + lvds differential data input (b2-b5,hs,vs , de) 15 vss ground 16 clkin- - lvds differential clock input 17 clkin+ + lvds differential clock input 18 vss ground 19 nc no connection 20 nc no connection 21 nc no connection 22 nc no connection 23 nc no connection 24 nc no connection 25 nc no connection 26 nc no connection 27 nc no connection 28 nc no connection 29 nc no connection 30 vbl- led power return 31 vbl- led power return 32 vbl- led power return 33 nc no connection 34 blim pwm for luminance control 35 bl_en bl on/off 36 nc no connection www.datasheet.co.kr datasheet pdf - http://www..net/
19 of 32 au optronics corporation product specification auo nbbu spec. version:0.3 37 vbl+ 6v - 20v led power 38 vbl+ 6v - 20v led power 39 vbl+ 6v - 20v led power 40 bist/ct2 bist/connector test* note1: start from right side 6.4 interface timing 6.4.1 timing characteristics basically, interface timings should match the 1280x 800 /60hz manufacturing guide line timing. parameter symbol min. typ. max. unit frame rate - 50 60 - hz clock frequency 1/ t clock - 69.3 72 mhz period t v 808 816 1023 active t vd 800 vertical section blanking t vb 8 16 - t line period t h 1320 1408 2047 active t hd 1280 horizontal section blanking t hb 30 135 t clock note : de mode only www.datasheet.co.kr datasheet pdf - http://www..net/
20 of 32 au optronics corporation product specification auo nbbu spec. version:0.3 6.4.2 timing diagram www.datasheet.co.kr datasheet pdf - http://www..net/
21 of 32 au optronics corporation product specification auo nbbu spec. version:0.3 6.5 power on/off sequence vdd power and lamp on/off sequence is as follows. i nterface signals are also shown in the chart. signals from any system shall be hi-z state or low level when vdd is off. power sequence timing www.datasheet.co.kr datasheet pdf - http://www..net/
22 of 32 au optronics corporation product specification auo nbbu spec. version:0.3 7. connector description physical interface is described as for the connecto r on module. these connectors are capable of accommodating the f ollowing signals and will be following components. 7.1 tft lcd module connector name / designation for signal connector manufacturer ipex or compatible type / part number 20347-340e-12 mating housing/part number i-pex 20345-040t-31 or 20475-040t-## or compatible www.datasheet.co.kr datasheet pdf - http://www..net/
23 of 32 au optronics corporation product specification auo nbbu spec. version:0.3 8. dynamic test 8.1 vibration test test condition(non-op): acceleration: 1.5 g frequency: 10 - 500hz half sine wave sweep: 60 minutes each axis (x, y, z) 8.2 shock test spec: test condition(non-op): acceleration: 220 g , half sine wave active time: 2 ms pulse: +/-x,+/-y,+/-z , one time for each side remark: 1. ambient condition is 25 + 5 , relative humidity : 40% ~ 70% 2. non-packaged and non-operation www.datasheet.co.kr datasheet pdf - http://www..net/
24 of 32 au optronics corporation product specification auo nbbu spec. version:0.3 9. reliability items required condition note temperature humidity bias ta= 40 , 90%rh, 300h high temperature operation ta= 50 , dry, 300h low temperature operation ta= 0 , 300h high temperature storage ta= 60 , 35%rh, 300h low temperature storage ta= -20 , 50%rh, 300h thermal shock test ta=-20 to 60 , duration at 30 min, 100 cycles esd contact : 8 kv air : 15 kv note 1 note1: according to en 61000-4-2 , esd class b: some perf ormance degradation allowed. no data lost . self-recoverable. no hardware failures. www.datasheet.co.kr datasheet pdf - http://www..net/
25 of 32 au optronics corporation product specification auo nbbu spec. version:0.3 10. mechanical characteristics 10.1 lcm outline dimension www.datasheet.co.kr datasheet pdf - http://www..net/
26 of 32 au optronics corporation product specification auo nbbu spec. version:0.3 www.datasheet.co.kr datasheet pdf - http://www..net/
27 of 32 au optronics corporation product specification auo nbbu spec. version:0.3 11. shipping and package 11.1 shipping label format 11.1 shipping label format 23m www.datasheet.co.kr datasheet pdf - http://www..net/
28 of 32 au optronics corporation product specification auo nbbu spec. version:0.3 11.2 carton package 11.3 shipping package of palletizing sequence www.datasheet.co.kr datasheet pdf - http://www..net/
29 of 32 au optronics corporation product specification auo nbbu spec. version:0.3 12. appendix: edid description address function value value value hex hex bin dec 00 header 00 00000000 0 01 ff 11111111 255 02 ff 11111111 255 03 ff 11111111 255 04 ff 11111111 255 05 ff 11111111 255 06 ff 11111111 255 07 00 00000000 0 08 eisa manuf. code lsb 06 00000110 6 09 compressed ascii af 10101111 175 0a product code 24 00100100 36 0b hex, lsb first 60 01100000 96 0c 32-bit ser # 00 00000000 0 0d 00 00000000 0 0e 00 00000000 0 0f 00 00000000 0 10 week of manufacture 01 00000001 1 11 year of manufacture 12 00010010 18 12 edid structure ver. 01 00000001 1 13 edid revision # 03 00000011 3 14 video input def. (digital i/p, non-tmds, crgb) 80 10000000 128 15 max h image size (rounded to cm) 1d 00011101 29 16 max v image size (rounded to cm) 12 00010010 18 17 display gamma (=(gamma*100)-100) 78 01111000 120 18 feature support (no dpms, active off, rgb, tmg blk #1) 0a 00001010 10 19 red/green low bits (lower 2:2:2:2 bits) 50 01010000 80 1a blue/white low bits (lower 2:2:2:2 bits) c5 11000101 197 1b red x (upper 8 bits) 98 10011000 152 1c red y/ higher 8 bits 58 01011000 88 1d green x 52 01010010 82 1e green y 8e 10001110 142 1f blue x 27 00100111 39 20 blue y 25 00100101 37 21 white x 50 01010000 80 22 white y 54 01010100 84 23 established timing 1 00 00000000 0 24 established timing 2 00 00000000 0 25 established timing 3 00 00000000 0 26 standard timing #1 01 00000001 1 www.datasheet.co.kr datasheet pdf - http://www..net/
30 of 32 au optronics corporation product specification auo nbbu spec. version:0.3 27 01 00000001 1 28 standard timing #2 01 00000001 1 29 01 00000001 1 2a standard timing #3 01 00000001 1 2b 01 00000001 1 2c standard timing #4 01 00000001 1 2d 01 00000001 1 2e standard timing #5 01 00000001 1 2f 01 00000001 1 30 standard timing #6 01 00000001 1 31 01 00000001 1 32 standard timing #7 01 00000001 1 33 01 00000001 1 34 standard timing #8 01 00000001 1 35 01 00000001 1 36 pixel clock/10000 lsb 12 00010010 18 37 pixel clock/10000 usb 1b 00011011 27 38 horz active lower 8bits 00 00000000 0 39 horz blanking lower 8bits 87 10000111 135 3a horzact:horzblnk upper 4:4 bits 50 01010000 80 3b vertical active lower 8bits 20 00100000 32 3c vertical blanking lower 8bits 10 00010000 16 3d vert act : vertical blanking (upper 4:4 bit) 30 00110000 48 3e horzsync. offset 30 00110000 48 3f horzsync.width 20 00100000 32 40 vertsync.offset : vertsync.width 36 00110110 54 41 horz&vert sync offset/width upper 2bits 00 00000000 0 42 horizontal image size lower 8bits 1e 00011110 30 43 vertical image size lower 8bits b2 10110010 178 44 horizontal & vertical image size (upper 4:4 bits) 10 00010000 16 45 horizontal border (zero for internal lcd) 00 00000000 0 46 vertical border (zero for internal lcd) 00 00000000 0 47 signal (non-intr, norm, no stero, sep sync, neg pol ) 18 00011000 24 48 detailed timing/monitor 00 00000000 0 49 descriptor #2 00 00000000 0 4a 00 00000000 0 4b 0f 00001111 15 4c 00 00000000 0 4d 00 00000000 0 4e 00 00000000 0 4f 00 00000000 0 50 00 00000000 0 51 00 00000000 0 www.datasheet.co.kr datasheet pdf - http://www..net/
31 of 32 au optronics corporation product specification auo nbbu spec. version:0.3 52 00 00000000 0 53 00 00000000 0 54 00 00000000 0 55 00 00000000 0 56 00 00000000 0 57 00 00000000 0 58 00 00000000 0 59 20 00100000 32 5a detailed timing/monitor 00 00000000 0 5b descriptor #3 00 00000000 0 5c 00 00000000 0 5d fe 11111110 254 5e 00 00000000 0 5f manufacture 41 01000001 65 60 manufacture 55 01010101 85 61 manufacture 4f 01001111 79 62 0a 00001010 10 63 20 00100000 32 64 20 00100000 32 65 20 00100000 32 66 20 00100000 32 67 20 00100000 32 68 20 00100000 32 69 20 00100000 32 6a 20 00100000 32 6b 20 00100000 32 6c detailed timing/monitor 00 00000000 0 6d descriptor #4 00 00000000 0 6e 00 00000000 0 6f fe 11111110 254 70 00 00000000 0 71 manufacture p/n 42 01000010 66 72 manufacture p/n 31 00110001 49 73 manufacture p/n 33 00110011 51 74 manufacture p/n 33 00110011 51 75 manufacture p/n 45 01000101 69 76 manufacture p/n 57 01010111 87 77 manufacture p/n 30 00110000 48 78 manufacture p/n 36 00110110 54 79 manufacture p/n 20 00100000 32 7a manufacture p/n 56 01010110 86 7b manufacture p/n 30 00110000 48 7c 20 00100000 32 www.datasheet.co.kr datasheet pdf - http://www..net/
32 of 32 au optronics corporation product specification auo nbbu spec. version:0.3 7d 0a 00001010 10 7e extension flag 00 00000000 0 7f checksum d9 11011001 217 sum 5888 www.datasheet.co.kr datasheet pdf - http://www..net/

▲Up To Search▲

Price & Availability of B133EW06-V0

	To Download B133EW06-V0 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .